Workshop
Start a discussion

Topics with Label: Storage and Cleaning

lindasjohn
Budding Contributor
10 replies

Hi. I want to put up carniya sz25 brackets from bunnings in garage for some shelving space. Its going aganist what i think is cement brick, although n ...

Razzer
Junior Contributor
21 replies

Here is a build that I did in my garage. It is made mainly out of 18mm MDF. I have attached a before and after photo. The vertical draws are to hold 1 ...

fhk56
New Contributor
3 replies

For many many years, I have been using plastic containers for small parts etc. After years of use these are now falling apart and spreading their cont ...

damo_
Budding Contributor
3 replies

I have a very small space for my shed - it's 1.1m X 3.6m (so more or of a glorified cupboard) that I was keen to make the most of so generally vertica ...

Wayne
Super Contributor
33 replies

Tara86
Super Contributor
29 replies

We recently had our council hard rubbish clean up so figured it was a good time to organise the storage under our stairs. Our biggest problem was a ...

Ari
Junior Contributor
2 replies

Hi Everyone I'm about to order the Absco 2.26 x 0.78 Shed for the space in the picture below. https://bit.ly/33OI1U7 I'm after advice regarding th ...

MonkeyLearn
Junior Contributor
8 replies

Hi Everyone,I've had problems with rats for quite a long time but now that I've started expanding my power tool collection I would like to protect the ...

Super66
Established Contributor
2 replies

I made what I am calling a Half Port, because I didn’t have room for a whole Car Port. So I just welded up a few brackets and add some polycarbonate ...

AngelaJ
Budding Contributor
9 replies

Hello! Might anyone have any tips on sealing an old timber-framed Colorbond garage with concrete floor from filling with up with dust, leaves, spiders ...

lcooksey88
Budding Contributor
15 replies

Love our garage make over to increase storage space & most importantly create a functional space for everyone!                

Seaton
Established Contributor
38 replies

G’day one and all, Ive just come across this site - how awesome is it! Anyway i’ll kick off my fist post with my 12x6 timber framed double gara ...

prettyliving
Super Contributor
1 reply

 A few months back my husband & I built some shelves and a workshop space in our garage. We don’t have a shed but we extended our garage when we buil ...

MonkeyLearn
Junior Contributor
6 replies

I'm building a few things out of pallets including shelves, tables etc. and I was wondering about what the best way to finish them would be. I have a ...

Baggs
Budding Contributor
12 replies

Hey hey. After the shed was finished I needed a work bench. After a lot of searching on the net I found the basic design I was after and went from ...

BrendanB
Budding Contributor
9 replies

Jimi
Junior Contributor
8 replies

To get the tools out of the garage, I built a solid steel shed from scratch. Far from an expert welder, I sourced the steel beams from a local supplie ...

pneri
New Contributor
3 replies

Hi everyoneI am just wondering if anyone would know where i can purchase a 4" T-Dust extractor fitting here in Australia, or even any size? RegardsPhi ...

Handyandy180
Budding Browser
1 reply

Hi All I'm in the process of building a 7ft x 7ft or 2134mm (Timber shed. Ive been able to source free timber and the build is at the frame stage (flo ...

Ginjourney
Newbie
2 replies

Im a bit of a newbie at DIY and home owning. I have a garage that is a bit tight for two cars but has a separate lockable part of about 2 x 3m. I have ...

ksd050
New Contributor
1 reply

Little project to sort out a tool storage & bits and pieces trays. Before... After... The smaller draws just slide on the shelves, the big draw at the ...

Super66
Established Contributor
2 replies

I could never find the right spot to put all my tape...So I 3D printed some brackets to put dowl rod in to hold the tape on my peg boardI love it, I c ...

Seaton
Established Contributor
1 reply

I've created some 3D printable parameterised small part boxes for workshop drawer organisation (and the OCD in us) that are fully customisable as I wa ...

Madmoggy
Established Contributor

My local MAKEROOM guy came to my aid . Nigel had the same problem of storing all your bits in one easy to get place. And an easy way to sort themas th ...