Workshop
Ask a question

All Topics

All Topics

Hi, recently a replacement rangehood was installed at my home and the installer cut holes through the double brick wall for the duct but left quite some damage to the internal and external brickwork ... See more...
Hi, recently a replacement rangehood was installed at my home and the installer cut holes through the double brick wall for the duct but left quite some damage to the internal and external brickwork and there is a hairline crack in the mortar above the hole. They didn't use a hole saw so they drilled multiple smaller holes and they used a broken brick some wood and Styrofoam to fill the hole for the previous rangehood pipe. This area is located in a roof cavity of a verandah. Is there potential for the damage to become worse? What sort of tradesperson would be best suited for the repairs?   Thanks JerryM     
We recently renovated our powder room. We have a Queenslander and at some point in it's history a toilet was added to the back of the house. As we have redesigned the house we ended up moving th... See more...
We recently renovated our powder room. We have a Queenslander and at some point in it's history a toilet was added to the back of the house. As we have redesigned the house we ended up moving the original toilet to make way for a hallway and added the powder room.   Happy Renovating    Claire  TT IG  Blog Steps Step 1 1. Framed up the space  Once we had a new location we framed in the new powder room, insulated and sheeted he wall.   Step 2 Step 2: Plaster and Sand Once drywall was hung it was time to finish these walls and get them paint ready. That meant filling each of the screw holes and taping each of the plaster board joints. I used plaster tape and ran it down the joints on the ceiling and walls where needed. I definitely believe plastering is an artform, one I have not mastered - But A for effort .    I apply the plaster along the line to fill to the grooves then run a wider trowel down to  even it out. You want to mix the plaster a little in your container to warm it up so it goes on smoothly.  You will often get air bubbles. I left it over night to dry then sanded the next day, I used an orbital Sander to smooth out the joints and the screw holes. I always have to apply a second coat of plaster, much lighter to smooth out the imperfections. Leave it once again for 24 hours or until dry then sanding once more.  You want to run your hand over the wall to feel for an grooves or rought spots, even though they may not be obvious now, they will be once you start painting. So you may need to sand a little more or apply more plaster. Finally we now have blank canvas to start creating.   Step 3 Step 3: Woodwork We designed the paneling around the bathroom mirror as it has to be centre of the sink and center of the paneling box. This gave us our starting measurement. I had originally planned for  double box paneling but due to the size of the room and the mirror, once it was marked out on the walls we realised single paneling would be better.   We found all of the trim we needed at Bunnings. To save a little money on the skirting boards cut down plywood that we had left over and added a small decorative trim to the top. This made the board look more custom and helped it tie in nicely with the style of the boxes. Step 4 Step 4 Painting   Although I’m not a huge fan of green my vision for this room has always been green! How strange is that! Nothing else worked, even though I looked at blues and whites I kept coming back to a green palette. I had a vision in my mind and that moody 20’s powder room had to be green.   I used Field of Green by British Paints. I primed and then applied 2 coats of paint. I colour drenched the room for a more dramatic effect. I love colour drenching small rooms as they look and feel bigger as, without the contrast, they're easier on the eye. Step 5 Step 5 Decorating   I love upcycling and creating a custom look on a budget. I found this great vintage mirror, circa 1950's on marketplace. It was originally on a dressing table, we removed it from the backing and mounted it directly to the wall using the original bracket.   We used a scew in 2 of the brackets which screwed directly into the timber stud. We used hollow wall anchors to mount the remaining 2 brackets.   Step 6 I found this washstand, circa 1920's, in one of our local thrift stores and it was absolutely perfect for the space.  I added a thrifted basket and some decor to finish the space.  
Indoor Garden Setting up an indoor garden is a great way to bring some greenery into your home and improve air quality. Here’s how to set up an indoor garden in 5 steps:   Happy DIYing    ... See more...
Indoor Garden Setting up an indoor garden is a great way to bring some greenery into your home and improve air quality. Here’s how to set up an indoor garden in 5 steps:   Happy DIYing    Claire  TT IG  Blog Steps Step 1 Choose a Location   Select a spot with good natural light, but avoid direct sunlight, which can cause overheating. Consider the humidity and temperature requirements of your plants. Step 2 Select Your Plants   Choose plants that thrive in indoor conditions, such as low-light plants like Chinese Evergreen or Spider Plant, or herbs like Basil or Mint.   There are many beautiful and low-maintenance indoor plants that can purify the air, improve the aesthetic, and even boost your mood!   TIP: There are a lot of indoor plants you can procreate, so you can build your indoor garden overtime at very little cost.   Here are some popular options:   Snake Plant (Sansevieria Trifasciata): Known for its air-purifying qualities and ability to thrive in low-light conditions.  Spider Plant (Chlorophytum comosum): Easy to care for and great for beginners, spider plants are also excellent air purifiers. ZZ Plant (Zamioculcas zamiifolia): A low-maintenance plant that can tolerate neglect and is great for busy people. Dracaena (Dracaena spp.): With over 40 varieties, Dracaena is a versatile and adaptable plant that can grow in a range of lighting conditions. Philodendron (Philodendron spp.): A popular choice for hanging baskets or pots, Philodendron is easy to care for and can grow in a range of lighting conditions. Peace Lily (Spathiphyllum wallisii): A beautiful plant with elegant white blooms, Peace Lilies are known for their air-purifying qualities and ability to thrive in low-light conditions. Rubber Plant (Ficus elastica): A stylish and low-maintenance plant with large, dark green leaves. Aloe Vera (Aloe barbadensis): A succulent with healing properties, Aloe Vera is easy to care for and can thrive in a range of lighting conditions. Pothos (Epipremnum aureum): A versatile and easy-to-care-for plant that can grow in a range of lighting conditions. Boston Fern (Nephrolepis exaltata): A lush and green plant that prefers bright, indirect light and regular watering.   Remember, choose a plant that fits your lifestyle and care level, and don’t hesitate to ask for advice at your local nursery or gardening store!   Step 3 Prepare the Soil and Containers   Use a well-draining potting mix and containers with good drainage holes. Consider using self-watering planters or pots with built-in water reservoirs.  My preference is having pots that will drain to avoid too much sitting water.  Step 4 Set Up Lighting and Watering   Consider using grow lights if your location doesn’t receive sufficient natural light. Water your plants when the soil feels dry to the touch, and avoid overwatering.   TIP: Stick your finger in the soil to the knuckle, if the soil is dry it’s time to water them.   Some indoor plants love a little humidity so misting the leaves is a great way to keep them happy. I do this weekly.   TIP: I have chosen a mister and watering can that go nicely with my decor so I can leave them out as a reminder to water and mist my plants. Step 5 Step 5: Maintain and Enjoy   Fertilize your plants regularly, prune them to maintain shape, and monitor for pests.   Enjoy the benefits of your indoor garden, including improved air quality and a calming atmosphere. Some popular indoor gardening options include:   Window boxes Hanging baskets Vertical gardens Terrariums Indoor herb gardens   I personally love to use unique items rather than the standard planting shelves.   Remember to research specific care requirements for your chosen plants to ensure a thriving indoor garden!  
Hi team - the cistern of our toilet fell off for a second time.   The first time, the head snapped off the screws inside the cistern (two screws hold it to the wall) so I had plumbers come in to ... See more...
Hi team - the cistern of our toilet fell off for a second time.   The first time, the head snapped off the screws inside the cistern (two screws hold it to the wall) so I had plumbers come in to fix it, but I've now discovered that instead of removing the old green plug and snapped screws, they just screwed a second screw into the wall of the green plug (see photos)... This second screw has also now snapped.   So the original green plug is still there, with the broken screw still in it, and now a second broken screw next to it.    I need to remove these but have no idea how - I tried a 2mm drill bit into the green plug but I can't get much in there, and no way of pulling the whole lot out as I can't get any purchase on the plug with pliers etc.   Any ideas?   Thanks    
Hi,  I’m a bit new to the whole sanding game. And I really want to refurbish a chest of drawers and stain it. But before I buy it I want to make sure I can do it.  I have stripped paint from ... See more...
Hi,  I’m a bit new to the whole sanding game. And I really want to refurbish a chest of drawers and stain it. But before I buy it I want to make sure I can do it.  I have stripped paint from a vanity before and I know how to stain wood. But I don’t know if I can do the same with particleboard and fibreboard.  I know with regular wood like timber you can sand it down and stain it. But from what I’ve seen online most people with draws made of particleboard or fibreboard they only paint over it, not sand it down or stain the wood.  I would love some suggestions on what I should do as I really want to update an ikea chest of draws and then sand and stain it rather then paint over it.   thank you!
Hi, Our alfresco area is supported by two SHS steel posts (120mm x 120mm x 5mm). We were wondering what the best way would be to cover these up? They are currently painted but looking at something su... See more...
Hi, Our alfresco area is supported by two SHS steel posts (120mm x 120mm x 5mm). We were wondering what the best way would be to cover these up? They are currently painted but looking at something such as a cladding/render/timber look. Is this possible? Any help would be great! Thank you.
Materials Mothers day Chrysanthemum our daughter gave her mother was kept and grown hydroponically. The amaranthus was grown, it grew so well, it blocked the foot path. Hence, cut them ba... See more...
Materials Mothers day Chrysanthemum our daughter gave her mother was kept and grown hydroponically. The amaranthus was grown, it grew so well, it blocked the foot path. Hence, cut them back and made a modern cascade flower arrangement. We're off to Bunnings to get some more mothers day Chrysanthemums for more flower arrangements. Regarding the amaranthus, Bunnings have tips on growing them. https://www.bunnings.com.au/diy-advice/garden/planting-and-growing/how-to-grow-and-care-for-amaranthus Tools Used some decking timber and a dowel to make the support. Cut the bottom off a soft drink container, attatched it with a bolt and put in floral art foam. Added flowers. 
I am not at all someone who usually complains and I have several times contacted Bunnings to say how wonderful a particular staff member is. Your customer service is absolutely excellent. Thank you s... See more...
I am not at all someone who usually complains and I have several times contacted Bunnings to say how wonderful a particular staff member is. Your customer service is absolutely excellent. Thank you so much. However, I have often noticed that the Bunnings guide to the measurements of items is not always accurate, as I've seen that the same item simply in a different length may have the other measurements that do not match, this makes making a decision very difficult. Can this be looked into please? The Width Height Depth are often mixed up and the actual measurements are in the wrong order, this is very confusing. Because I'm disabled, I always shop online before coming to Bunnings to find out where in the store an item is and often use Click and Collect (great service). Thank you Bunnings, from Jan Lamb
Hi, I'm buying a for a 3m x 1.5m x 2m shed from Bunnings and having them install it. I'm a disabled pensioner on a tight budget and so any help would be greatly appreciated. I'm almost 70 years old... See more...
Hi, I'm buying a for a 3m x 1.5m x 2m shed from Bunnings and having them install it. I'm a disabled pensioner on a tight budget and so any help would be greatly appreciated. I'm almost 70 years old and so the shed and flooring only needs to last for about 10 - 15 years. However, I am a renter and so cannot lay a concrete stab to attach it to. I'm thinking of using treated pine pallets as flooring, is that suitable  (if not, why please) or is there another type of inexpensive flooring that I can use (preferably under $200)? Also, I've just found out that I need to insulate the shed, I noticed the foil type insulation at Bunnings, is that suitable, and how does it get attached to the shed. (preferably under $200). Or is there something less expensive to insulate my new shed as the total cost of having a shed is really adding up, I had no idea that the shed would need insulation too. (preferably under $200). Can I pay extra to have the people installing the shed to also install the insulation? Thank you so much for answering these questions. Regards Jan, a very long time Bunnings shopper.
does anyone know of a spray which will control onion weed in lawn?
      Hi,  I planted 2 silver princesses in our front yard last spring. One has taken off while the other hasn’t done much at all and has different coloured leaves. They were p... See more...
      Hi,  I planted 2 silver princesses in our front yard last spring. One has taken off while the other hasn’t done much at all and has different coloured leaves. They were planted at the same time, get the same sun water etc. any ideas? (Photos of healthy and unhealthy plant attached) 
First time building in NSW. Will these small gaps around windows outside be filled with silicon as standard?   
Hello Team,  We have recently moved to a property that has (what looks to me like) a Citrus Tree - guessing it's a Lemon Tree but someone may be able to say otherwise. It looks like it is being eat... See more...
Hello Team,  We have recently moved to a property that has (what looks to me like) a Citrus Tree - guessing it's a Lemon Tree but someone may be able to say otherwise. It looks like it is being eaten by something and doesn't look very healthy. Any tips on how to revive and turn it into a healthy tree? Thank you!
Hello I would like to render this rough bagged wall. I have watched the Bunnings how to video but was wondering if there were any tips and tricks that would help with my project. I will use Da... See more...
Hello I would like to render this rough bagged wall. I have watched the Bunnings how to video but was wondering if there were any tips and tricks that would help with my project. I will use Davco off white render and then paint. Should I add bondcrete to the mix? How do you get a sharp edge over   the rounded brick top? Any guidance would be helpful! Thank you! Cococat  
I want to split the cold water supply for my kitchen sink/tap so that i can still use the sink normally but I can also have another supply going to my water cooler. What do you recommend the best spl... See more...
I want to split the cold water supply for my kitchen sink/tap so that i can still use the sink normally but I can also have another supply going to my water cooler. What do you recommend the best splitter ill be and what is the standard thread size? I have seen 1/2, 15mm.
Hi Guys  I have to build up a deck with 90x45 H3 treated pine i have couple of question if anyone can help me  1) which paint i can use to protect the timber framing i m already using joist deck ... See more...
Hi Guys  I have to build up a deck with 90x45 H3 treated pine i have couple of question if anyone can help me  1) which paint i can use to protect the timber framing i m already using joist deck tape but i need to protect all of the framing  2) which screws and what size i have to used it for joists 3) I have look the treated pine screws it has 2 options one is with Countersink Head screw Drive and the other one is Countersink Rib Head Philips drive  Thanks  
Hello. I am a new member to this community. We need help with our garage. We are planning to apply epoxy prior to moving. The garage is new. Do you think we need to pressure and acid clean it prior t... See more...
Hello. I am a new member to this community. We need help with our garage. We are planning to apply epoxy prior to moving. The garage is new. Do you think we need to pressure and acid clean it prior to applying? From the prep to the final coating, how many days is the process and curing time? 
Hi. I have 2 x  8.5kg swap and go bottles on my caravan but need to move the stone guard and put in 2 x 3.7kg bottles. Is it possible to swap the 8.5kg bottles for 3.7 kg ones?
I have an old square wooden table (180cm x 80 approx), what will be the cost to laminate (marbel looks) or paint it?
I am wanting to paint an old wooden coffee table. Am stickering the top and want a quick spray paint for the legs. We have a pet galah that wanders the house and often sits on strata underneath coffe... See more...
I am wanting to paint an old wooden coffee table. Am stickering the top and want a quick spray paint for the legs. We have a pet galah that wanders the house and often sits on strata underneath coffee table....I've never seen her eat the wood of table but there's always a first with birds. Fully aware to paint in area away from birds and not bring back til totally dry.....but is dry spray paint bird friendly....or a certain brand better than another in this instance?