Workshop
Ask a question

Topics with Label: Tools and Materials

KarenMM
Just Starting Out
2 replies

A couple of window sills in my home are very weathered from sun damage and in a bad state with cracks in the wood. The sills are not rotten (yet) and ...

badmojo
Getting Established
1 reply

Hi Bunnings Workshop Team, I want to install a smart door lock. What is the appropriate lock for below?  

H-M
Just Starting Out
4 replies

Hi Team I have removed and internal wall in my 1967 home only to find the Ash floor boards don't flow all the way through. I am looking to cut them b ...

redcamper
Finding My Feet
5 replies

Hi, I'm planning to build an office table using the Practa 2200 x 600 x 26mm Acacia Timber Benchtop. If I don't want to use table legs, how do I mount ...

Kumar
Just Starting Out
2 replies

On using Deta make smart switches & by the use of grid connect app on the phone, can we dim the lights? If yes, then does the app provide / display a ...

Matt_R
Community Newcomer
1 reply

Hi I am wondering what is the best way to fill a palm sized hole in an internal wooden door? Would you use a foam filler with putty over it? Or shou ...

shirley123
Just Starting Out

I have lived in my home for 30 yrs and have a black slate floor throughout most of the house. I have sealed it several times with gloss sealer. I have ...

Dom123
Community Newcomer
1 reply

Hi. I want to build a right hand opening internal door. I guess a pre hung door system would be easiest. The problem is that the Bunnings online shop ...

amySA
Cultivating a Following
4 replies

I have purchased these shelf brackets and have attached them to the wall successfully. I am unsure which screws to use to secure shelf to the top sid ...

Alyse1
Community Newcomer
3 replies

Hi all - I am trying to make a low picnic table on a budget. I have some old outdoor chairs that are falling apart, and I am hoping to re-purpose the ...

harryl111
Just Starting Out
1 reply

    The absence of gutters on the metal roof causes water to pour directly down the walls, splashing onto the brickwork beneath the window sills and ...

juliee1
Just Starting Out
1 reply

I am going to tile the corner behind my wood burning heater. What adhesive should I use? It’s a ceramic subway tile onto painted white set. FYI, bur ...

joeharis
Just Starting Out
6 replies

Hi im newbie here, thank you for letting me join this awesome group. I'm thinking to build outdoor bench using mgp10 untreated pine and metal pipe leg ...

annaluno
Getting Established
1 reply

Hello, I'm helping my sister out as she would like to remove the whole door frame and door etc and keep it as a wall for more space inside for her l ...

victoriacalhoun
Just Starting Out
9 replies

Spray Tan Salon renovations / advice on skirting boards. Hi everyone. I am in the process of renovating what used to be my garage, however, it is now ...

HJS
Just Starting Out
5 replies

We have metal transition strips between tile and floating wooden floors. I hate them - to make matters worse, the builder (years ago) used different s ...

raerific
Just Starting Out
7 replies

just moved into this rental and the grout is horrendous. Seems like someone painted the grout lines white and paint has chipped overtime. What is the ...

Mark270481
Growing in Experience
12 replies

Novice painter here,used Tauberman ultimate enamel paint to repaint my architraves and door frames however I found that there were these thick deposit ...

moloko
Growing in Experience
1 reply

Hello, Some areas of my interior cement render walls have been patched up and the look of the patched areas look as expected, very flat and smooth c ...

1250
Finding My Feet
10 replies

My front door does not fit tight to the frame therefore allowing a draught to come into the house. The space is around the entire door including the b ...

rochester
Getting Established
4 replies

Hey all, My house has cypress pine floorboards that have seen better days - Pic attached. The floor itself looks in pretty decent shape, few little ...

ezzie
Growing in Experience
3 replies

After years of never ever being able to load and use a caulk gun, I grabbed a friendly geezer at Bunnings and declared my frustration with caulk guns, ...

Lee777
Getting Established
17 replies

Guys, Im looking at installing 13mm solid jarrah floor boards on existing concrete slab. Do you have any videos/publications on:- Preparation A ...

nerea
Cultivating a Following
11 replies

Hey guys. I'm painting my house and need advice with which filler to use to fill small cracks and big holes in the walls. I need something easy to us ...