Need advice for deck construction

kaitolin

Hi there, wondering if anyone could give me some advice 🙂

For context, my deck build will not be attached to the house and be about 600mm high. The below rough sketch shows where my bearers and posts would go (the left bearers are placed to avoid pipes along the house wall). I was gifted sixty 140 x 45mm joist hangers, so I am thinking I will use 140 x 45mm joists and double these up for bearers on 100x100mm H4 posts. There is a garden bed/ retaining wall to the right and I want to add a privacy screen along the right side of the deck, as tall as possible, likely utilising 1800x902mm merbau alternating slat fence, but horizontally. 

My main questions are:

1. I have seen some decks where instead of the joists sitting on top of the bearers they hang between them. When is this okay to do? As I have free hangers, would it be worth doing this? For example for more air circulation/ a bigger crawl space. 

2. I have seen 101 different ways of putting in posts/stumps. What's best practice for longevity? (Preferably without breaking the bank). The two posts on the far left are situated on an existing concrete pad that is sloped away from the house, what should I use here to have a level foundation rather than digging holes? 

3. How should I attach the bearers to the posts? I have seen them be strapped directly on top (but if my bearers are 90mm and my posts 100 - assuming this won't work?), notched (this wouldn't work with my 90 x 140mm bearers though), bolted in from the side, etc. 

4. How best to make and attach a privacy screen on the deck? I have seen people attach things directly to the top of the deck or to existing gazebo posts that come through the deck (unsure if these posts are cemented into the ground or attached to the frame of the deck). Either way, would my posts on this side of the deck need to be stronger to support this? 

Any advice would be greatly appreciated! 

JacobZ

Hi @kaitolin,

Thank you for your questions about your upcoming decking project.

You've got a great plan in place already that will make a fantastic deck that will be extremely strong.

As with any larger project like this, the first step I'd advise is to contact your local council to check whether you need building approval and the assistance of a draftsperson or engineer. A quick phone call can help direct your next steps.

I'll answer your questions individually and then offer some general advice and ask a few questions.

1. Joist hangers are fine to use in almost all situations and with careful planning of the frame, I can't say I've come across anywhere you couldn't use joist hangers. Using joist hangers in your circumstance would be perfectly ok and considering you've got some for free, it makes sense to design the deck accordingly.
    
2. Where new posts are being installed, I'd always recommend full stirrup post anchors that are wet set into the concrete. They elevate the posts slightly so water can run beneath them, minimising the potential for your posts to rot. In high wind environments, use Pryda High Wind Post Anchors. 
   
   Where there is existing concrete, like the pad near your back door, use Pryda Bolt Down Post Anchors w Raised Mount to achieve the same slightly raised post. You can use packers underneath the post anchors to level them before bolting them in place.
    
3. With your design, there is no real reason to double up your bearers and with the posts you are using, realistically it's best not to. 
   
   Following the relevant Bearer Span Table, 140 x 45mm H3 Treated Pine Framing can span 1400mm between posts, which assuming your scale is relatively accurate, your bearers are within.
   
   With this being said, you can cut a 45mm wide and 140mm deep notch on one side of your posts for the bearer to sit on. You can then bolt the bearer to the post.
    
4. The best way to attach a privacy screen at the far right of your deck, would be to continue the posts up above the height of the finished deck. The bearer can still sit in a notch on these posts without terminating the post at that height. Continuing the posts up and above this height will allow you to run horizontal rails between the posts to attach your merbau screening. Your posts shouldn't need to be stronger to support this. 
    

Now for some general advice and questions for you.

As I mentioned above, there's no real need to double up your bearers as all your spans are well within the guidance of the relevant Timber Span Tables. This will reduce your material costs without reducing your deck's strength.
 

At 600mm above ground, you are not legally required to install a handrail or balustrade, but it is worth considering, especially if you'll have young children on the deck.
 

Have you decided which direction you'd like your decking to run? Have you thought of how you'd like to finish the edges of your decking? 

These things can affect how you build your frame, so thinking about these things in the planning stage is worth doing so you can factor them in early.

All in all, you already have a fantastic plan in place, and I'm excited to see it develop further and eventually become a reality.

Let me know if you have any further questions or info to add.

Jacob