how to remove screws from curtain rod and wall. They seems to be stuck and would move.
Please see below pics. One is on rod and another one on wall.
You would use the pliers to try and unscrew the screws @softkun123. You might need to pull slightly as you do to prevent the inside section from spinning within the wall.
Mitchell
Hi @softkun123,
It looks like the screw heads on your curtain rod bracket have been stripped, which makes them tough to remove with a standard screwdriver. I’d recommend first trying to undo the bolt on the side that connects the front mounting bracket to the rear—if you can loosen or remove that, it should give you better access to the screws currently hidden behind the front bracket. Sometimes you can grip the head of the bolt with locking pliers while you turn the nut on the back, which may help free it up.
If that doesn’t work, and the screws are still stuck, you might want to try using a screw extractor bit. These are designed specifically for stripped screws and can help bite into the damaged head so you can back them out. We have a few extractor kits available that work with a standard drill. Just go slow and apply steady pressure so you don’t damage the wall further.
I note the stripped screws fixing the bracket into the wall have a Phillips and flat head formed in them. Try switching to a flat head screw driver for them as the Phillips bit is stripped out.
Please let me know if you have any questions.
Hi @MitchellMc Thanks. Yes I am struggling to remove front bolt and screw as well. I tried but it won rotate at all. Hence I directly tried remove one on the wall.
I'd concentrate on trying to remove the side bolt first, @softkun123. Place a Phillips head screwdriver in it and then use an adjustable spanner to turn the nut on the outside. Do not turn the screwdriver as it will slip. Only use it to try and hold the screw in position whilst you turn the nut with a spanner.
It's the type of thing that, with the correct tools and technique, it would likely only take a handyperson a few minutes to undo. If you continue to struggle, it might be worth employing one to do the job.
Further i was able to remove front rod. But now the problem is screws in wall are stuck. As seen in the attached pics it's one of hollow wall anchors.
How do I dettach screws or remove anchors from wall?
You could use the screw extractors I linked to above, try unscrewing them by gripping the heads with pliers, or use a flathead screwdriver instead of the phillips.
Do I need to apply force to pull it ? Or it should unscrew whilst anchors remaining inside wall cavity. I am afraid wall might damage.
Thanks it's fixed and I was able to remove screws and rod.
hi
I need to fix this hole as seen in pics. I had removed curtain rod. How can I fix it?
You could use Spakfilla to fill the hole and then sand to a smooth surface, or you might find this Selleys Spakfilla Wall Repair Kit useful. After repairing the hole, you'll need to apply two coats of primer and then, when dry, paint.
Hi
After removing curtain tracks, I can see wood from hole slightly upper side where originally installed. Please see attached pics.
Can I use this wood to install curtain tracks red marks in the pic?
If so what sort of screws would be required?
As per pics it's approx 4 cm deep and there's is void in between.
However, I am not sure the length of wood and whether it span across the top of windows.
Thanks @MitchellMc
Can I use attached 2 products together as seen in pics?
The plasterboard joint tape and spakfilla rapid 180g
Yes, you can, @softkun123.
Take a plasterboard peice that is larger than the hole. Mark the sides of it over by keeping it covering the hole. Then use a plasterboard knife to cut along the lines. Now take a length of wood that is bigger than the hole. Insert it inside and screw it on to top and bottom of existing plasterboard. Insert the new peice and screw it in. Use plaster tape on the gaps and plaster the entire place. After drying you can choose a new spot for curtains
Ideally you want to screw into the studs rather than a timber that has a void between it and the plasterboard. You might find a stud detector helpful when trying to locate mounting points. Here's a useful guide: How to use a stud finder. It's unlikely that you'll find studs in the correct locations for your mounting brackets, but it's always good to check first. Even if you can get a couple of point screwed directly into timber that's more secure than having all mounts in the plasterboard.
Thanks @MitchellMc . I tried finding stud but couldn't find it.
Would you say it's safe to use timber which is approx 4 cm away from wall?
There should be vertical studs every 450 or 600mm across the wall @softkun123.
You could possibly use the timber you've found, but given it's recessed 4cm into the wall, it's hard to tell whether it would be a solid method for connection.
After applying sparkfilla below are the images how 2 different spot looks.
Is it good enough?
Not quite @softkun123. You're doing a good job, though. You need to apply another thin, consistent coat over the whole area and sand it smooth. You don't want to be able to see the tape or have any of those gaps. One nice smooth coat.
When you run your fingers over the area it should be smooth.
How about spot 2? Is there an issue with that as well?
It's hard to tell from an image @softkun123. Typically, you would want one smooth plaster-covered surface without tiger stripes. I'd imagine that when you run your fingers over it, you'll be able to feel the stripes. If you can feel inconsistency with your fingers, you'll likely be able to see it after painting.
