Hi folks, I haven't posted much or commented for a while. Have had a few health issues.
I have been working on my replacement of my kitchen and bathroom bench tops, from Laminate to Live Edge River Red Gum timber slabs. Which as you can imagine take a bit more work than you average bench tops, more so as it's the very first time I've tackled such a mammoth task.
So thought I would share some of what I've been working on.
Any tips or handy hints are greatly appreciated.
1st top coat on sink vanity slab.
I still have a ways to go, but I feel like I have the hardest under my belt ~ besides finding some muscles to move them from my messy shed to the house. So far I only have the under side of the bench tops sealed and one top coat of marine grade varnish on the underside of my vanity slab.
Wish me luck.
This is a truely inspirational project you have going on which I have been waiting for with bated breath. That timber is absolutely amazing!
For your final topcoats, you might like to try a test section using Uni-Pro 4 Piece Foam Brush Set. I've found that with numerous types of topcoat I get the best finish with them instead of the recommended application tool. I hold them at a very shallow angle and drag them across the surface almost letting them float on it. I've found they leave little to no "brush strokes" and produce a brilliant finish.
We can't wait to see the finished slabs installed. Well done on a fantastic job this far!
Thank you @MitchellMc your praise is very appreciated. It's taken me this long as I keep doubting what to do next and get advice and then rethink my original ideas. Thinking others ideas could be better than what I'd originally decided to do..
So far I've only been working on the under side of my 3 slabs, 2 x kitchen, one being a breakfast bar kitchen sink side and the other having the hot plates and a small amount of bench top either side.
I started on the smallest slab 1st as when I had them delivered the guy wasn't very obliging and put the biggest one on top and I couldn't move it. So it sat for some time, till I practically begged my daughter to help me try and slide the smaller one out from underneath, almost dropping it down my shin. NOT a good idea.
But I have made a big boo boo on one of my slabs. I thought I would mix black oxide with my wood putty to fill up the gaps instead of the car bog and oxide I was using. The big problem being it's stained my timber and now the only way I can get rid of it that I've been able to find thus far is sanding. I have read of other ways but mostly information from the USA and I would rather hear it from a local or more reliable source. Possibly someone on here may have some ideas on easier ways to go about removing the stains I've left with the black oxide on my timber slabs? If so please feel free to comment. I'm a bit chicken to do too much for fear of making it worse, or damaging my slabs.
Thanks @MitchellMc for the suggestion of using the foam Brushes, I've used them for a great many years on inside craft work/tasks, with great success. So will give it a go as I have a coat to put on the tops side of my bathroom slab soon.
This old gal
As I said before @MitchellMc thank you for your suggestion of the foam applicators. I tried them and just didn't like the flow, or should I say lack of flow as when I went to feather the start and end of application, it seemed to drag and make little grip scrap/marks which I thought would flatten out in the drying process. But didn't so instead of being my last coat, I've given it another sand and coat with a bigger foam applicator and will see how that goes.
It's a big area, and with winter being close the days are colder so I am apprehensive of coat times and temperatures in which I can put another coat on and I have two other slabs to get done. I feel that i may now have to wait till spring as our days a shorter and colder. Unless I bring them inside and keep the temp consistent unlike in my shed/workshop. Could be messy. Any suggestion would be appreciated.
This old gal
Thanks for the feedback! If you have bigger foam applicators then I would definitely be using them instead of the smaller ones. It's a pity they didn't work out well for you, but it is about using the best tool for the job, so if you are getting better results with something else stick to it. When I've used them, I was more using it to maneuver the coating around and not using it to apply the coating. I would pour on a heavy coat and then float the applicator on the liquid dragging it around instead of 'brushing' it on.
I can't wait to see the finished top installed as you are doing a fantastic job!