Workshop
Start a discussion
since August 2020
Online
DexterOz
Established Contributor
  • My latest posts
  • Posts I liked
  • My liked posts

User's latest posts

DexterOz
Established Contributor
2 replies
yesterday

Thanks @MitchellMc all good. Thanks for explaining. Below is what i initially planned getting a big board 2400 * 1200 * 16 mm and get cuts to specs an ...

DexterOz
Established Contributor
4 replies
yesterday

Thanks @EricL i will go and check it out also i was thinking then i would also need bench or more supporting tools.

DexterOz
Established Contributor
1 reply
yesterday

It is basically a walk in robe, i just wanted to start with one side and see how i go

DexterOz
Established Contributor
9 replies
Friday

Bummer i went to bunnings today to get the cuts but i got a mixed reply. Team member said if its less than 300mm then we can not cut . So now need to ...

DexterOz
Established Contributor
Monday

Thanks @MitchellMc

DexterOz
Established Contributor
12 replies
a week ago

I have updated the measurements, the space was not a perfect square some reason the back is a bit smaller not sure how but to eyes it looks normal. 1) ...

DexterOz
Established Contributor
2 weeks ago

Thanks @EricL good point I just measured at the bottom to assume it was square. i will again measure fromfront to back and add that 2mm margin.Thanks ...

DexterOz
Established Contributor
15 replies

I have wardrobe with no shelves or partition, so i want to build standalone insert shelves that sits betweenthe current partition. I have tried to mea ...

Posts user liked

Bunnings Team Member MitchellMc
Bunnings Team Member
yesterday

I really like @Noyade's approach of using the existing cabinetry @DexterOz. Please allow me the opportunity to contact your local store to discuss ...

Bunnings Team Member MitchellMc
Bunnings Team Member
3 replies
yesterday

I apologise for the confusion, @DexterOz as this appears to be an interpretation issue. It would be my understanding that we should be able to cut ...

Bunnings Team Member EricL
Bunnings Team Member
5 replies
Friday

Hello @DexterOz I'm sorry to hear that you couldn't get your timber cut. I'm afraid 300mm is the limit of the cutting service. However, this would be ...

Noyade
Valued Contributor
2 replies
Friday

Hi Dexter! "I have wardrobe with no shelves or partition" Possibly an act of heresy on a Bunnings forum and I don't wanna cramp your desire to build - ...

Bunnings Team Member MitchellMc
Bunnings Team Member
11 replies
a week ago

Hi @DexterOz, The Trojan 75mm Mitre & Corner Clamp will assist in you joining the corners at 90 degrees with Zenith 8G x 40mm Countersunk Rib Head C ...

Arcc
Junior Contributor
4 replies

Hello everyone. It has been quite some time since I last submitted a project to these Bunnings DIY boards. I have been very busy over the last six mon ...

Bunnings Team Member EricL
Bunnings Team Member
14 replies
2 weeks ago

Hello @DexterOz When you are fitting a cabinet into an existing space. It is very rare that the actual space is square. You'll sometimes notice that ...

TedBear
Valued Contributor
1 reply
March

Hi @DexterOz ,I have to agree with both @MitchellMc & @redracer01 that there is little option but to start tracing the water connections back throu ...

User's liked posts

DexterOz
Established Contributor
2 replies
yesterday

Thanks @MitchellMc all good. Thanks for explaining. Below is what i initially planned getting a big board 2400 * 1200 * 16 mm and get cuts to specs an ...

DexterOz
Established Contributor
Monday

Thanks @MitchellMc

DexterOz
Established Contributor
12 replies
a week ago

I have updated the measurements, the space was not a perfect square some reason the back is a bit smaller not sure how but to eyes it looks normal. 1) ...

DexterOz
Established Contributor
2 weeks ago

Thanks @EricL good point I just measured at the bottom to assume it was square. i will again measure fromfront to back and add that 2mm margin.Thanks ...

DexterOz
Established Contributor
15 replies

I have wardrobe with no shelves or partition, so i want to build standalone insert shelves that sits betweenthe current partition. I have tried to mea ...

DexterOz
Established Contributor
March

Thanks for your valuable suggestion @TedBear and @redracer01 yes certainly next thing i will spend some time dig and take the sprinkler out. Hopefully ...

DexterOz
Established Contributor
4 replies
March

Hi @MitchellMc Thanks , I tried to check the below1) turning off/on the valves , it controls the sprinklers in the backyard.2) took out the top pop u ...

DexterOz
Established Contributor
6 replies
March

@JaneK i have moved in and never seen the ones on left side work, As far as i understand they are all same "Orbit" brand and looks similar. If the im ...

Contact Me
Online Status
Online
Date Last Visited
yesterday