Workshop
Start a discussion
since June 2019
December
Seaton
Established Contributor
  • My latest posts
  • Posts I liked
  • My liked posts

User's latest posts

Seaton
Established Contributor
December

Thanks @MitchellMc that was very helpful. I thought this might be the case as I didn't have any luck in finding any information online, hence my po ...

Seaton
Established Contributor
2 replies

As a bit of background, we don't have any air-conditioning in our current house, but as its an old house (+80 years old) has high ceilings, in summer ...

Seaton
Established Contributor
July

I forgot to add.... Make sure the g-code being produced is for your machines controller, I'm assuming GRBL here. Whatever application you 're using se ...

Seaton
Established Contributor
July

I found PVC fittings don't really work as they measure from outside or is it inside, anyway they don't fit because 100mm PVC fittings is not equal to ...

Seaton
Established Contributor
1 reply
July

Can you see a new serial port other than com1 and com2 when you plug in the device? if not then most likely you don't have the serial port driver loa ...

Seaton
Established Contributor
June

I must admit I'm predominately battery now, with the exception of a few tools, some historic some not. I too have been a fan of the Ryobi System for a ...

Seaton
Established Contributor
June

looks awesome, well done!!!

Seaton
Established Contributor
1 reply

I've created some 3D printable parameterised small part boxes for workshop drawer organisation (and the OCD in us) that are fully customisable as I wa ...

Posts user liked

prettyliving
Super Contributor
1 reply
April 2020

Do you have an idea what new flooring you will be putting in eventually? If it were me I would remove the carpet in those sections before installing. ...

Yorky88
Super Contributor

SalBay
Junior Contributor
4 replies
November

That's pretty much how I would approach it. Although I would use Tee hinges for the leg attachment, and magnetic catches to hold the legs up while fol ...

Noyade
Super Contributor
1 reply
December

"already crammed with things" My shed became so crammed I created workbenches outside between trees with plenty of shade. The car now happily lives un ...

r23on
Super Contributor
November

I was going to build this work bench but I have been focused on woodturning to get it underway. I have completed the conversion from imperial to metri ...

Razzer
Junior Contributor
27 replies

Here is a build that I did in my garage. It is made mainly out of 18mm MDF. I have attached a before and after photo. The vertical draws are to hold 1 ...

ProjectPete
Trusted Contributor
32 replies

Quick job ticked off the liston the wknd - installing screening with a creeping plant to hide our hot water systems. Nothing fancy, nice and easy - do ...

Bunnings Team Member MitchellMc
Bunnings Team Member
1 reply
December

Hi Stephen (@Seaton), I've contacted Haron, one of our ceiling vent suppliers, and they have advised that the location of the vent is a personal pre ...

User's liked posts

Seaton
Established Contributor
December

Thanks @MitchellMc that was very helpful. I thought this might be the case as I didn't have any luck in finding any information online, hence my po ...

Seaton
Established Contributor
July

I forgot to add.... Make sure the g-code being produced is for your machines controller, I'm assuming GRBL here. Whatever application you 're using se ...

Seaton
Established Contributor
July

I found PVC fittings don't really work as they measure from outside or is it inside, anyway they don't fit because 100mm PVC fittings is not equal to ...

Seaton
Established Contributor
1 reply
July

Can you see a new serial port other than com1 and com2 when you plug in the device? if not then most likely you don't have the serial port driver loa ...

Seaton
Established Contributor
June

I must admit I'm predominately battery now, with the exception of a few tools, some historic some not. I too have been a fan of the Ryobi System for a ...

Seaton
Established Contributor
1 reply

I've created some 3D printable parameterised small part boxes for workshop drawer organisation (and the OCD in us) that are fully customisable as I wa ...

Seaton
Established Contributor
1 reply
May

Great find thanks for sharing, I learnt something from it

Seaton
Established Contributor
May

Hi @Conair400 I suggest you look at using some online lighting calculators and use the specs of the lights you're looking at to see what lumens are g ...

Contact Me
Online Status
Offline
Date Last Visited
December