Workshop
Ask a question
since October 2024
Saturday
LorenClayton
Having an Impact
  • My latest posts
  • Posts I liked
  • My liked posts

User's latest posts

LorenClayton
Having an Impact
Tuesday

Success! I just went in & asked. The guy suggested that I get this Stanley set because he said it had the triwing bit, which it did, but it was too bi ...

LorenClayton
Having an Impact
2 replies

Hello I want to dismantle & clean my Anko box fan but it has these triwing screws. Does Bunnings have a suitable screwdriver for these? Some people ...

LorenClayton
Having an Impact
3 weeks ago

Thank you Mitchell, I'll see how I go.

LorenClayton
Having an Impact
2 replies
3 weeks ago

Thank you Jacob. No, they're not aligned (trick of perspective - see photo). I think the link I provided wasn't the right choice. Maybe it should be 3 ...

LorenClayton
Having an Impact
4 replies

Hello https://www.bunnings.com.au/suntuf-3-6m-opal-corrugated-polycarbonate-roofing_p1015525 Would this panel be OK if I placed it in the back cor ...

LorenClayton
Having an Impact
1 reply
3 weeks ago

Hello, just updating with photos of my new benchtop, Polytec Portofino stone which I'm very happy with. I believe the height of the laminate is abou ...

LorenClayton
Having an Impact
4 weeks ago

Thank you Mitchell.

LorenClayton
Having an Impact
2 replies
4 weeks ago

Hello, I've installed 8 rolls of merbau. Do the undersides of the slats need a sealant against moisture, being directly on concrete? I haven't painted ...

Posts user liked

Bunnings Team Member MitchellMc
Bunnings Team Member
1 reply
3 weeks ago

Hi @LorenClayton, Essentially, you need to create a solid edge for fixing the polycarbonate sheets. The soffit in that area isn’t structural, so you ...

Bunnings Team Member JacobZ
Bunnings Team Member
3 replies
3 weeks ago

Hi @LorenClayton, Although this is not it's typical use, as long as it is supported, you could use polycarbonate roofing as a wall material to preve ...

Bunnings Team Member MitchellMc
Bunnings Team Member
1 reply
4 weeks ago

The act of painting or applying oil helps protect the timber, @LorenClayton. So, if they are to be sitting on the concrete, I would definitely paint t ...

Bunnings Team Member MitchellMc
Bunnings Team Member
4 replies
4 weeks ago

Hi @LorenClayton, Yes, it would be best to flush it with water for a few days before installing the Merbau, as it may bleed some tannins after the f ...

Bunnings Team Member JacobZ
Bunnings Team Member
6 replies
a month ago

Hi @LorenClayton, The closest thing I could find to a white picket fence is this Matrix 890 x 290mm Picket Garden Edging. They would be somewhat fle ...

Bunnings Team Member MitchellMc
Bunnings Team Member
1 reply
a month ago

Hi @LorenClayton, Unfortunately, painting over a rough, textured render will not remove the texture. Multiple coats of paint may slightly soften the ...

Bunnings Team Member MitchellMc
Bunnings Team Member
3 replies
October

Hi @LorenClayton, In your current setup, the sink is already sitting higher than the benchtop, so you’re familiar with how that looks and fun ...

Bunnings Team Member JacobZ
Bunnings Team Member
3 replies
October

Hi @LorenClayton, I'll start by saying it is always going to be difficult to colour-match-stained timber, as the colour is relative to the timber it i ...

User's liked posts

LorenClayton
Having an Impact
Tuesday

Success! I just went in & asked. The guy suggested that I get this Stanley set because he said it had the triwing bit, which it did, but it was too bi ...

LorenClayton
Having an Impact
1 reply
3 weeks ago

Hello, just updating with photos of my new benchtop, Polytec Portofino stone which I'm very happy with. I believe the height of the laminate is abou ...

LorenClayton
Having an Impact
4 weeks ago

Thank you Mitchell.

LorenClayton
Having an Impact
2 replies
4 weeks ago

Hello, I've installed 8 rolls of merbau. Do the undersides of the slats need a sealant against moisture, being directly on concrete? I haven't painted ...

LorenClayton
Having an Impact
October

Perfect answer! Thanks Mitchell. I was hoping that's the case. I might actually go with the laminated Acacia to be on the safe side and I prefer the l ...

LorenClayton
Having an Impact
1 reply
October

Hello Jacob The Bondall Jarrah stain worked a treat. I just used 240 sandpaper rather than the stripper, with 2 coats over 2 days. I was very carefu ...

LorenClayton
Having an Impact
October

Thank you Jacob, I'll give that a go.

LorenClayton
Having an Impact
October

Thank you Mitchell. Great idea! I'll get some today.

LorenClayton's Bookmarks
No posts to display.
Contact Me
Online Status
Offline
Date Last Visited
Saturday