• Whole of House
  • Kitchen
  • Bathroom and Laundry
  • Living and Bedroom
  • Garage and Shed
  • Outdoor
  • Garden
  • Featured Projects
  • How To
  • Top Ideas
  • Best Advice
  • About Us
Workshop
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
Ask a question
Share a project
Sign in
Join Workshop
  • Bunnings Workshop
  • >
  • Albums for Community
  • >
  • Images in Profile (JustJim)
  • >
  • My Images for JustJim

My Images for JustJim

My Images for JustJim

  • Albums
  • All images
Image Options
  • Flag Image for Review
  • Bookmark
  • Subscribe to RSS Feed

Album: Profile (JustJim)

by JustJim
Doubles as an outfeed table
Hang ten!
Wide view
Closer view
Wood rack
If you look closely you can actually see the growth spurts from ordinary plywood to scraps of film-faced plywood.
Don't they look great together? You can hardly even see the leg grafts.
I routed out extensions of the saw's mitre slots so that the crosscut sled, or any others, could move forward with the outfeed table in place.
Positioning guide. Has been glued and brad nailed here. Has since been screwed. I haven't.
Towel roll holder close up.
Towel roll holder showing location on the tool wall.
The foolishly named 'kerfmaker'.
The very useful, multi-purpose plank of wood with holes in it.
My silver Giaco Whatever designed Maker Knife arrived today. Does anyone else have one? The black ones were shipped a few weeks ago but the silver ones had to have their anodisation re-done.
The tape and string rack. Oiled up and hanging by a French cleat.
Push shoe. Two bits of wood glued together with two bits of masonite glued to them!
Crosscut sled from below showing runners and the open safety box.
Crosscut sled from the rear or operator's end. Note the bright "No Hands Here" safety box.
Crosscut sled from the front (the end away from the operator).
Face jointing jig rear view showing modifications I had to make to fit the lock of my rip fence.
Face jointing jig sitting over the rip fence and with the sawblade embedded into it.
20190316-_5007992-StoolParts.jpg
20190316-_5007993-StoolDryFit.jpg
20190318-_5007996-StoolPainted.jpg
20190325-_5008015-TraysOnBench.jpg
The lower of these two shelves seemed ideal.
20190325-_5008018-Sanded.jpg
20190325-_5008020-TestFit.jpg
20190330-_5008024-Painted test fit.jpg
20190330-_5008028-Nailed in place.jpg
20190330-_5008029-Dividers fitted.jpg
One a penny, two a penny, hot cross buns. Fresh out the oven.
20190330-_5008033-Frnished rack.jpg
Detail of corner reinforcement.
Empty caddy showing atrocious routing attempts!
This space intentionally blank.
Propane and propane accessories. No wait…
Sawblade set to random angle that looked good.
Assembled and fixed.
Screwed into position.
Close up of hanging saw.
Tongue and Dado joint in plywood
Box frame with tongue and dado joinery
The long sides were cut upright against the fence.
The ends were cut flat on the table.
Long side being routed for box bottom.
Masonite base dry fitted.
I'm ready for my close up, Mr DeMille.
Arbor spanner in place.
Chipper block empty.
20190316-_5007992-StoolParts.jpg
Previous
20190316-_5007992-StoolParts.jpg
Next
Added March 2019
0 Likes
Like
Posted in: Timber workshop stool - ( August 2021 )

You must be a registered user to add a comment on this image. If you've already registered, please log in. If you haven't registered yet, please register and log in.

  • Comment
Workshop Resources
  • Contact Us
  • Rules of participation
  • Terms of use
  • Privacy
  • Workshop help
Our Sites
  • Bunnings Australia
  • Bunnings New Zealand
Quick Links
  • Register
  • Sign in
Go to Bunnings