The Bunnings Workshop community can help with your home improvement projects.
Hi
I replaced my 23-year-old, 12m deck with new marabou slates in June 2023, and then in October 2023, I treated them with Cabots Merbau Aquadeck Exterior Decking oil. Throughout the process, I was continuously getting advice from the experts at Bunnings.
Now, I feel it’s time to give the deck a bit of a refresh, especially since the heavy traffic areas have gotten quite dirty. I’ve attached some current photos for you to take a look at. Could you please let me know what steps I should take now and what materials would be best to make the deck look brilliant again?
Thanks so much!
Syed
Solved! See most helpful response
Hi Syed (@smhasnain),
While your deck still looks great, it looks like it's time for a maintenance coat of oil to have it looking brand new.
Start by giving your deck a good clean with Cabot's Deck Clean and a Long Handle Deck Scrub Brush. Check out How To Clean a Deck for some guidance.
Once clean, the process is much the same as what you did initially. Apply 1-2 coats of the Cabot's Merbau Aquadeck Exterior Decking Oil with an oil applicator and a paint brush. Check out How To Oil Your Deck for guidance on this process.
Let us know how you go and if you have any questions along the way, please don't hesitate to reach out.
Jacob
Hi Jacob,
Thank you for your prompt reply. I am wondering if you could also explain the difference of using Aquadeck oil over water based stain (Merbau) on my slates. Can i apply any of this on cloudy day when ambient temperature is less than 20degree. Thanks
Hi @smhasnain,
Aquadeck, and more specifically, Cabot's Merbau Aquadeck Exterior Decking Oil is a decking oil with merbau coloured water-based stain added.
If you were to use just a stain, you would have to apply another product over the top. It's just easier to use the oil and stain combo, so I'd suggest sticking with it.
You can apply your oil on any day where the temperature is between 10-30 degrees, but if there is rain forecast, I would put it off till the weather clears.
Let me know if you have any further questions.
Jacob
Thank you very much for your valuable advice and guidance.
I have cleaned the deck and attached some images for your reference. I’ve noticed that certain areas of the boards appear to have darker, more brownish patches compared to the rest of the surface. I would appreciate your advice on how to address this inconsistency in colour. Should I scrub these areas further or consider using sandpaper to achieve a more uniform appearance?
Additionally, I have a few other questions:
I would greatly appreciate your expert advice on the above points. Thanks
Hello @smhasnain
In its current condition if you were to oil it now, there is the possibility that some sections will be darker than others due to the stain of the old oil still on the surface. It's also possible that some sections will not absorb the oil properly because there are still sections of your deck that are sealed with the old oil. In order to get a uniform finish, I suggest sanding the entire surface back to wood. This will remove all the unevenness of the surface and bring you back to the original surface of the wood.
Once the decking panels have been sanded and cleaned properly, you can then make your plans on staining its surface. Please do not mix stains as they are not compatible with each other and will produce an unreliable finish. I suggest using only one product for your entire deck, I recommend visiting your local store and looking at the oil and stain sample board in the paint department so that you'll have a better idea of what the finish colour will look like.
Here are some handy step-by-step guides:
If you need further assistance, please let me know.
Eric
Hi Eric,
Thank you so much for your valuable advice — I really appreciate it! I’ll go ahead with the hand sanding using 200-grit sandpaper on the boards that show signs of old oil before applying a fresh coat to the entire deck. Is this ok? I’ll also avoid mixing stains as you recommended.
Just one quick question: I have about 3 litres of Cabot’s Aquadeck in Merbau left over from around 4 years ago. Would it still be okay to use on the boards, or would you recommend buying a new tin of Aquadeck?
Thanks again for your help!
Best regards,
syed
Hi @smhasnain,
I think you'll find the grit would be 240, as I haven't seen 200 before. If 240-grit doesn't remove the previous coating, you can try using 180-grit.
I suspect three-year-old oil might be at the end of its usable life. The pigments have likely sunk to the bottom of the can, and it might be difficult to get them into suspension again. I'd recommend buying some new oil as you don't want to go to the effort of sanding and have old oil ruin the finish.
Mitchell
Workshop is a friendly place to learn, get ideas and find inspiration for your home improvement projects
We would love to help with your project.
Join the Bunnings Workshop community today to ask questions and get advice.