Workshop
Ask a question

The Bunnings Workshop community can help with your home improvement projects.

D.I.Y. paling fence

mich1972
Kind of a Big Deal
mich1972
mich1972
Kind of a Big Deal

 

Pine palings used to replace a wooden fence wrecked by termites.

 

IMG_3861.jpeg

 

The project

 

Part of our backyard paling fence was rotting and warped due to termite damage years ago that we had treated but didn’t have the time to replace.

 

IMG_3831.jpeg

 

The section of fence is behind our shed and lately we have had a few unwelcome visitors jumping the fence and running through our backyard. So, we decided to make the fence taller to put them off. We did it in a day, starting early in the morning before the heat set in. 

 

IMG_3825.jpeg

 

Finally, we made time to fix it and our neighbour kindly helped us, as we had helped them with their paling fence. It was only one section that was the worst. Eventually we will replace the rest of the fence, which is a little warped, but fine.


We laid out all of the materials the day before.

 

I_MG_3820.jpeg

 

We also had the tools laid out in the shed ready to go, along with a good extension cord to run from the shed to the back fence. That was for the drop saw to cut all the timber and a trestle table setup as well. 

 

IMG_3819.jpeg

 

Have a couple of mini trestle tables on hand when you are doing a D.I.Y. project - it makes it so much easier to keep everything organised. 

IMG_3821.jpeg

 

Steps

 

Step 1

 

We pulled down the old paling fence, being extremely careful with the nails sticking out. 

IMG_3838.jpeg

 

We wore gloves, but be super careful with the old timber. We took it to our local recycling waste centre. 

IMG_3843.jpeg

 

Step 2

 

I'm not sure if you can see at the base but we had to remove heaps of sand the local council had put there when they put a new footpath in. The sand covered the base of the fence and because it was wet all the time, the termites moved in and caused havoc. We had to get that sorted out. 

 

IMG_3845.jpeg

 

We put in new timber attached to the posts for the boards. The cross beams were bolted in.  

IMG_3846.jpeg

 

Step 3

 

The planks were spaced out just enough so they could be overlapping each other. 

 

IMG_3850.jpeg

 

I’m sorry but I didn’t get a spacing size. 

IMG_3851.jpeg

 

The guys just used an off-cut plank that was trimmed down to use as a spacer. 

IMG_3852.jpeg

IMG_3857.jpeg

 

Step 4

 

Once the first layer of planks were attached, the second layer of planks was added. 

 

IMG_3859.jpeg

 

We were very lucky our neighbour had a nail gun. It just made it so much easier to work with. 

IMG_3860.jpeg

 

Step 5

 

We just replaced the old Colorbond capping and tek screwed it on. 

 

IMG_3861.jpeg

 

Now look closely at the gap at the bottom of the fence. We sorted that out, too, so it isn’t a safety hazard. 

IMG_3862.jpeg

 

Step 6

 

I only applied the used motor oil to the base of the fence to protect it. I had no idea it is an old remedy. 

 

IMG_3874.jpeg

Step 7

 

We placed concrete film into the gap.

 

IMG_3878.jpeg

 

 Back filled with blue metal. 

IMG_3881.jpeg

 

Then we cut off the excess film sticking out. 

IMG_3883.jpeg

IMG_3882.jpeg

 

Step 8

 

Replaced the capping. 

 

IMG_3885.jpeg

 

The capping is faded and bent out of shape in some spots but it was still OK to reuse it.

IMG_3889.jpeg

Step 9

 

This shows you how much better it looks now against the existing fence. We will get to that old part soon. 

 

IMG_3865.jpeg

We are so grateful to our neighbour for helping us. We always help each other out. So between the three of us, it took approximately five hours to complete. It was a messy project but it's well worth doing. I hope this project will help you if you have the same fence as us. 

 

IMG_3863.jpeg

 

Tools and materials

 

Materials used in the project:

 

 

Tools used in the project:

 

 

Comments
Noyade
Kind of a Big Deal

G'day Mitch @mich1972 

Looks like you had a good day - and a productive day! Well done! 👍

Dave-1
Community Megastar

Good Afternoon @mich1972 

:smile: I should have known it was your work! Thats a nice fence! And seriously love the way you have descibed and actually put the new one in.

 

I was most impressed with the gravel base and the protectrive sleeve to keep it seperated from the timber and allow drainage/support of the path at the same time. It really looks liek a professional fencing job :smile:

 

Dave

SyedJaffry
Growing in Experience

Great work :smile:

Why join the Bunnings Workshop community?

Workshop is a friendly place to learn, get ideas and find inspiration for your home improvement projects