Workshop
Start a discussion

The Bunnings Workshop community can help with your home improvement projects.

Three-tier deck and pergola

EricL
Bunnings Team Member
Bunnings Team Member

Re: Planning outdoor area - Ideas

Hello @Itai,

 

What an impressive build! This is by far is one of the most well thought out and meticulously planned decks I've seen built here on workshop. Thank you so much for sharing the photos and steps you took in building this deck. The extra measures you've taken to protect your deck will surely pay off in the long run. What an absolute pleasure to see it come together. I'm sure a lot of our members will be keen to ask you about the details of your build.

 

We look forward to seeing more, please keep us updated.

 

Eric  

See something interesting? Give it the thumbs up!
Reply
Loading...
Chaks_DIY
Super Contributor

Re: Planning outdoor area - Ideas

Loving your progeas with this ! Execution is on point 👍🏽

 

Regards

Rufaro 

----
Yours Kindly. For more, please follow @hausdiy_weekender
Reply
Loading...
Itai
Experienced Contributor

Three Tier Deck and Pergola

Hey all.

 

So I've finally completed all 3 tiers, just without the side panels yet. Below are my progress shots.

I must say, the lowest tier turned out to be much harder than I thought, even with the klevaklip system (maybe even because of it, lol!) ... mainly because my concrete had some weird slopes, and while the slope is down and to the right, it wasn't consistent. I levelled it a good few times with a long steel square tube and level, before eventually giving up on that approach and borrowing my neighbours laser level ... and I must say, it's the next best thing since sliced bread!

 

The mid tier was much easier as I just attached the wood to the ledger which was levelled, and because it was 190mm wood (for height control, not for structural reasons), there was no bend in the short lengths, so it was just really easy to level.

 

I also bit the bullet and bought the plunge saw, to straighten and align the boards on the main deck and lower deck. I really do wish I bought that at the beginning of my renovation last year. Though I've only made a few cuts, it's been so easy to get precise accurate cuts. My only gripe with the Ozito plunge saw is that when you put the 2 tracks together, they're unaligned like a 1mm or so, which means I can't get a perfect long straight cut. It is only a 1mm or so. But I'm a perfectionist! 

 

Here are the progress photos of the lower tiers.

 

Installing the Klevaklip system.

You'll see a few missing in the second row from the right. That's because I ran out. But as it turned out, the ones on the left, the slope was actually too high for some of the middle ones (uneven slope), so I ended up using 5mm thick angle brackets for those ones, and moved them into the 2nd row. The angle brackets were actually much sturdier, but less easy to level if I were to use them instead across the board. Another thing, is individually the klevaklips felt quite flimsy because the bolts would wobble a little in their seats. However, when all the wood was installed and everything tightened, the flimsiness disappeared. As you will see below, I did also put noggins in between most of the floor joists. I only skipped where I used an angle bracket as it just wasn't necessary.

I also made 2 errors which cost me a lot of time. The first, I just assumed all the lower deck's brackets needed 60mm bolts. This was very far off. Only 2 or 3 of the brackets needed them. So I had to undo all the brackets to remove them, and then I had to buy all sorts of different sized bolts, as if they were too short, the nut wouldn't be able to screw on (or I couldn't get the bracket high enough at all), and if they were too long the bolt would have been higher than the top of joist and get in the way of the decking board. Thankfully, Bunnings has a great return policy, so I bought a whole bunch of bolts in stepping up sizes (60mm, 75mm, 100mm, 110mm, 120mm) and returned what I didn't use. Amazing that the slope ended up being, that the lowest corner of the deck, I had to attached the bracket directly to the concrete without any bolts, and the highest corner I am using a 120mm bolt (around 65mm difference). Which is quite a slope over 4.2m (corner to corner diagonally).

The second mistake was that I measured everything out based on the lowest corner, assuming the joist would touch the bottom of the bracket, and levelled the entire deck to that. Then I installed the first joist, and it wasn't level and I was very very confused, so I levelled that first joist. And then the rest of the deck wasn't level to it, so literally spent hours trying to figure out what was going on, why I was so off, and relevelling everything (and ended up getting that laser from my neighbour). Once I had all the joists level, and was stumped because my maths was around 10-15mm off, I realised it was because I attached the first bracket to the ground directly, which meant the bolt head was above the bottom of the bracket line and I had needed to use a drill spade bit to create a recess in the wood for it. The instructions do say to do this, but I just forgot. I was super annoyed. But decided to stick with it ... I wasn't prepared to spend another day or two of disconnecting and relevelling everything again. At the end of the day, no one will notice and neither will I. I just means a bit more work for the side panels, which will be easy now with the plunge saw!

 

Itai_0-1625703830252.png

 

Itai_1-1625703913753.png

 

Itai_2-1625704108899.png

 

Itai_3-1625704255081.png

Itai_4-1625704325057.png

Itai_5-1625704384038.png

 

All finished (except the side covering)

 

Itai_6-1625704478844.png

Itai_7-1625704512002.png

Itai_8-1625704551018.png

 

Itai_9-1625704585925.png

 

Next steps in order:

- Finish the side panelling

- Add lighting to the side panelling between tiers - I'll be usingsmart RGB-W LED striplights in diffused chanels

- Build the raised garden bed for the main deck level

- Decide what to do and build the area between deck and fence for the lower level (I'd like to incorporate a water feature here, so am doing a bunch of research. The space is only between 32 - 39cm wide).

Fill the concrete section between the deck and garden with a sand or gravel or something for a firepit area.

- Install the EZ-glaze roofing (This is last because stock is only available in December. I will be using a clear plastic tarp in the meantime and hoping it doesn't rip in wind!)

 

Things to decide still:

- Do I make a built in BBQ area, or simply use a BBQ cart

- Do I put a screen up on the laundry side of the deck

- What sort of lighting we want

- Any other things I should do.

 

I'll likely only get to these next steps in the next 3-4 weeks as I've got a few other projects and occasions that will take precedence in the mean time, but should get back to it in August.

 

Regards

 

Itai

 

 

 

 

Reply
Loading...
EricL
Bunnings Team Member
Bunnings Team Member

Re: Planning outdoor area - Ideas

Hello @Itai

 

Thank you so much for that update on your decking project. I suggest a BBQ cart to allow you to find the best spot when cooking. Building a fixed BBQ area limits your choice of location. With a BBQ cart, you can move your cooking facilities to a better spot, especially when the wind and rain are very strong. 

 

Are you looking for a bright light source or something festive like Lytworx Warm White Connectable Double Filament LED Party Lights - 10 Pack? I have this set at home and they are so easy to join together. They provide more than enough light during those late-night get-togethers.

 

We look forward to seeing more once you've finished those last details on your list.

 

Eric

 

See something interesting? Give it the thumbs up!
Reply
Loading...
Itai
Experienced Contributor

Re: Planning outdoor area - Ideas

Hey Eric.

 

Yeah, that's what I'm thinking too. I love the asthetics of built in barbeques, but it does limit space. Also, means more time before you can begin to use the area! 

In terms of lights, thanks for sharing that link. I nabbed 4 packs of something similar from Bunnings on clearance, but I think the ones I grabbed aren't very strong lights. I'll see how they look once I set them up outside, if I need something stronger.

I am planning on putting one or two ceiling fans and two or so roof mounted strip heaters once I get the roof covering, so not sure if the string lights would get in the way? Do you know if strip heaters are any good in this kind of space where there is a roof, but no wall on 3 sides?

 

Thanks

 

Itai

 

 

Reply
Loading...
EricL
Bunnings Team Member
Bunnings Team Member

Re: Planning outdoor area - Ideas

Hello @Itai

 

The strip heaters are actually quite good but are limited by their stationary application. I recommend the Jumbuck Charcoal Gas Patio Outdoor Heater.  This allows you to move the heat to where it is needed most. It has an estimated coverage of at least 17 square meters and has a safety tilt mechanism that shuts it off in case it falls over. It has its own carriage wheels for ease of transfer and movement.

 

On the high setting, the Patio Heater is estimated to last at least 6 hours on a 9kg gas bottle, on lower settings it will extend it to 10 hours. You can purchase a cover hood when storing it during summer. It should be safe for your lights and fan as long as you observe the recommended distance for items near the heater.

 

Eric

 

See something interesting? Give it the thumbs up!
Reply
Loading...

Why join the Bunnings Workshop community?

Workshop is a friendly place to learn, get ideas and find inspiration for your home improvement projects