Workshop
Ask a question

Topics with Label: Repairing

Carolynk
Just Starting Out
2 replies

I just bought a Caroma Saracom kitchen mixer tap and the flow is slow, is this normal, if not is there a workaround for how it can be fixed?

Edgar
Growing in Experience
1 reply

I am replacing a laminated benchtop with a wooden benchtop that will be appropriately stained and sealed with several coats. Having seen the effects m ...

mrs_njr
Just Starting Out
9 replies

Hi All Can anyone please recommend quality brand names of taps where we can easily replace the washers ourselves please? We were advised not to buy t ...

clarkita
Just Starting Out
4 replies

Trying to dismantle a wooden kitchen Benchtop. How does one pull these screws apart? I need to separate the slabs. What tools do I need? Thank you!   ...

CD1956
Just Starting Out
1 reply

How to increase the cold water flow in a kitchen mixer Estelle brand

JerryM
Just Starting Out
1 reply

Hi, recently a replacement rangehood was installed at my home and the installer cut holes through the double brick wall for the duct but left quite so ...

AbdulHaddad
Just Starting Out
17 replies

How to replace a cartridge on a Mondella maestro level handle sink mixer?

smittyboi
Growing in Experience
10 replies

      I just recently had my benchtop installed and I’m very disappointed with the quality. They didn’t scribe it too the wall in the slightest and ...

jqi
Just Starting Out
1 reply

Hi, help, my mixer tap handle is broken. I’ve changed the washer on a similar model before and I know usually on the hot and cold round knob it can ...

preetik
Just Starting Out
1 reply

Hi all, My kitchen benchtop got burnt by placing hot pot and the surface is not smooth anymore and there is a mark. Refer the photo.     Is this fix ...

Christinesteinm
Just Starting Out
5 replies

Hi my kitchen corner cupboard door is leaning forward at the top touching the other door how do I fix it  

AmberLee22
Just Starting Out
1 reply

Can I get replacement clamp for this light or do I need to replace the fixture   completely? If so, is it safe to do it myself? TIA

Bell_1986
Cultivating a Following
4 replies

so it was time to move the dishwasher and give a clean, noticed appears some water swelling and rusted area.... also noticed top of bench wiping felt ...

marknorman
Just Starting Out
1 reply

mia011
Just Starting Out
1 reply

    Hi everyone, I was wanting to know best method to fix burn marks on kitchen MDF tabletop next to the stove without replacing the whole sheet ...

marissa
Finding My Feet
2 replies

Hello! I have recently discovered this burn mark in the middle of my kitchen bench and was seeking advice of how to fix it. Thanks!  

vas90
Getting Established
1 reply

Hi, I tried painting over the peeling spots, but it did not offer adequate coverage.What is the best way to approach repairing this? Window Seal by ...

Omphalie
Finding My Feet
3 replies

Hi, My water filter overflowed last night and water dribbled onto the kitchen floor all night without me noticing. I woke up in the morning to a few s ...

Shelltoo
Just Starting Out
2 replies

Hi, My mixer tap drips constantly, regardless of handle position. Looking for advice as to the likely cause before I disassemble anything. So far... ...

Robinord
Finding My Feet
9 replies

I bought this home not too long ago, I just noticed that the kitchen countertop right infront of my sink is expanding due to water leaking into the wo ...

SarahK1996
Building a Reputation
4 replies

   My parents just did a renovation inside our holiday caravan using a Kaboodle kitchen and there is one drawer that keeps sliding out because our c ...

jamesvtre
Just Starting Out
1 reply

I want to grout with a black grout. What black grout product would be ideal for this tile? Would this product be suitable https://www.bunnings.com. ...

rustyicon
Getting Established
14 replies

Hi All, I was putting some shopping away in my fridge & when i went close the top fridge door I noticed a crack. No idea how this happened, Is there a ...

twilight79
Getting Established
8 replies

Hi All, Hoping for some wisdom and expertise in getting this mixer arm/lever loosened and unscrewed/removed so I can change the washer. I tried wd ...