Workshop
Ask a question

Topics with Label: Heating and Cooling

lisamariedack
Community Newcomer
2 replies

Hello, looking to convert my cold brick garage to a playroom. Looking for cost effective and easy recommendations for insulating the walls? Could I wo ...

braddis84
Just Starting Out
2 replies

     morning all, I have. 5 by 8 shed that I am turning into a woodworking workshop. I have power being installed including 15amp power. I am putti ...

Girocopta
Just Starting Out
1 reply

I'd like ideas please on the best options for insulating my shed. It's not a big shed 6.7x 4.3    

bm_rphy
Just Starting Out
1 reply

This Garden Shed is approximately 3.5 x 2m. We're based in the Macedon Ranges so insulation/heating will be critical if this is to become an effective ...

adam_b
Finding My Feet
5 replies

Hi, I’m located in Adelaide and recently had a Colorbond garden shed installed in my backyard. Dimensions are 6.0m (L) x 2.3m (W) x 2.4m (H). It has a ...

Ask_Itee
Cultivating a Following
5 replies

I have a large garden shed that needs a roof vent. I purchased a bastion roof vent https://www.bunnings.com.au/bastion-300mm-aluminium-mill-roof-vent ...

VMcNamara91
Finding My Feet
3 replies

So we have moved to a property with a steel shed, 6m x 6m with a high gable roof and 2 roller doors. Concrete floor. I want to use the space for my cr ...

LisaAndStu
Just Starting Out
3 replies

I’m about to start a project to line the inside of my shed with a frame so I can have either plywood or vj board walls. While I’ve done quite a fair s ...

hellrazor
Getting Established
8 replies

I have a veranda almost enclosed to be like a shed. There is one section openwhere the is no colour bond that area has a mesh pull down blind I wan ...

Taco
Growing in Experience
2 replies

Hi, Was looking to put insulation in this shed ceiling before gyprock, can I use poly strapping to hold the insulation in place, if so how would I aff ...

Imz93
Finding My Feet
2 replies

I have a 3x3 tin shed i want to install insulation in. Ive looked into the foilboard option. If I choose foil board how do I glue it onto the surface ...

Loui
Just Starting Out
1 reply

      Hi, I have a 6x6m steel colorbond shed with 1 door, 1 window and a large double roller door. I want to insulate it and clad it with ply, ...

msgforsunil
Cultivating a Following
2 replies

Hello all I need to replace my garage door seal. Any recommendations? Few photos attached. Thank you   

anthward1972
Getting Established
10 replies

Hi all. I’m about to frame out the inside of the walls and ceiling in my colorbond shed using framing pine and then gyprocking it. I’m led to believe ...

Remarka6le
Amassing an Audience
5 replies

An ongoing total garage renovation into a functional home gym.   CONTEXT I've always been into sport and fitness; health and exercise were alway ...

Rona
Finding My Feet
5 replies

Hello Looking for advise please i have brought some aluminium flashing and silicone for sealing the inside and outside bottom of shed . Before insta ...

learningDIYer
Cultivating a Following
9 replies

Note: please, rental-friendly solutions only! This garage door is unusable so I’d like to seal it off from. Considering the garage door type and the w ...

Pata
Just Starting Out
3 replies

What is the best insulation to use to insulate a metal panel lift garage door facing east to protect from the heat? I have looked at all the options ...

Kitto
Finding My Feet
9 replies

Hi team, newbie on this forum. I have read through multiple shed insulating threads on here and elsewhere already but cannot seem to find the best s ...

jonmwilson
Just Starting Out
1 reply

I'm trying to insulate a very old shed - timber framed, and a mix of corrugated metal and timber cladding (three timber walls, roof and fourth wall me ...

spike05
Just Starting Out
4 replies

We bought our house with this outdoor room. My son uses it for his bedroom. It has aircon but the room still gets hot in summer and cold in winter. Th ...

Racsop
Finding My Feet
2 replies

I’ve seen a few threads but just interested to know what product should I be using? Is it some sort of sheet or board? Thanks!  

dirtman
Just Starting Out
2 replies

can I add insulation to a shed that has walls already framed? I was planning on using foilboard.

raficiskander
Just Starting Out
2 replies

Hi, I have a big garage, 6.6x6, in a TownHouse, which will be impossible to install a normal AC in, and I don't have windows to get a portable AC to ...