Workshop
Start a discussion

Topics with Label: Tools and Materials

IBuildStuff
Junior Contributor
27 replies

A couple of weeks ago, I picked up a little anvil for a very reasonable price off Facebook Marketplace. Now while I had no immediate need for an anvil ...

mervb
New Contributor
5 replies

Can I use foam under floor foam insulation for the ceiling of my garage.

Noyade
Valued Contributor
9 replies

I saw this in today's Aldi catalogue. 710 watts. Would this be a 'brushed' motor - therefore loud like a corded drill? Too small for an induction moto ...

Noyade
Valued Contributor
1 reply

In the mailbox today. Is this something new for Bunnings? Or did you have it last year? Very impressive quality - better than the butcher paper with l ...

Starkers_17
Junior Contributor
8 replies

In January 2020, I had the slab laid for my shed. The intention was to have my mates help me get this built over the next 12 months. I had a big ...

denk
New Contributor
4 replies

Hi everyone. I have a 10 year old Titan shed which is 9m x 6m in size. It gets awfully hot in QLD summers and I'm now deciding to insulate the walls ...

craftycrew
Occasional Browser
2 replies

Hi All, I've been thinking I'd like to change the flooring in my garage. It's currently concrete - old, grey and stained. The space I need covered i ...

Salini
Newbie
164 replies

Hi, I am looking for free pallets. I live in Sydney Inner West (Strathfield South). Thanks

terryandfaye
Budding Browser
1 reply

What common timbers for boat building are sold by bunnings?

Janine103
Newbie
2 replies

How do I paint a colourbond roller door? Paint is faded & comes off when wiped

jennb
New Contributor
5 replies

Hi... I live in my caran, to which I have attached a permanent wooden annexe. I want to put a tropical roof over my caravan and attach it to the exist ...

Noyade
Valued Contributor
2 replies

The rivet holds a steel stirrup to a plastic backingIf I drill it out - is there a Bunnings product/device to re-rivet it?A pop-rivet will not work. C ...

JudithW
Budding Contributor
7 replies

  One of the difficulties of renting, or even sharing a workshop with someone else, is where to set up for a major project - Especially during winter ...

JaneL
Frequent Browser
1 reply

Can anyone tell me how to install a colorbond roof on a cubby. The existing one is going rotten (the makers used untreated pine) although we painted ...

mitchiko
Occasional Browser
2 replies

hi there newbie here.. it's my first time making a table because I couldn't find the right size to match the space. I bought this specrite panel, wha ...

horti64
New Contributor
22 replies

i bought a 18v + one battery and fast charger kit and want to register them with ryobi for warranty, the charger doesn't have a serial number anywhere ...

Ricochet
Budding Contributor
89 replies

Hi. I have just bought an Ozito 12v cordless drill. Could I use the battery from that in an Ozito 18v Circular saw or other Ozito power tool.

totocol
Established Contributor
7 replies

I was hoping for some ideas to have a permanent outdoor space to store wood and keep it dry. I was thinking maybe using weatherboards to match the hou ...

MattR85
New Contributor
4 replies

Hi all, Just wanting some ideas on how to best waterproof and seal off the bottom of my shed. There are sides with significantly bigger gaps of whi ...

SLlo
New Contributor
3 replies

I think it should be fairly straightforward, however I am wondering what products and type of paint etc to use when painting a carport ceiling? The a ...

Wheresmy10mm
New Contributor
7 replies

My boxing punching bag stand broke. The metal snapped off and another part of it bent. It's quite thick, is this something a beginner can repair weld? ...

Sunda
Junior Contributor
7 replies

Hi, I am looking at balustrade options for the mezzanine floor of our shed. It is 2.4m above ground and am trying to figure out what are the econo ...

AnitaP
Junior Contributor
7 replies

This part of my drill press has broken and now the depth stop doesn't stop. Does anybody know if this part can be replaced? And if it can, what is it ...

DonGreen
New Contributor
5 replies

Thought I would give everyone a look at my latest project. I made a bench each for my 18V saw and my sliding compound miter saw. The saw are each on a ...