Workshop
Start a discussion

Topics with Label: Craft and Hobbies

fiddlerdan
New Contributor
1 reply

Chladni plates (see smithsonian link - deleted because of guidelines) refer to a vibrating plate onto which fine particles like tea, sand or salt are ...

IBuildStuff
Junior Contributor
53 replies

A couple of weeks ago, I picked up a little anvil for a very reasonable price off Facebook Marketplace. Now while I had no immediate need for an anvil ...

poppylee198
Budding Contributor
4 replies

Hello! We are looking to out some trellis and vines on the side of our shed to grow something as we look onto it from our outdoor area. There is no ...

Brad
Trusted Contributor
7 replies

On sale, expectations are not high but time will tell.

JaneL
Frequent Browser
1 reply
May

Can anyone tell me how to install a colorbond roof on a cubby. The existing one is going rotten (the makers used untreated pine) although we painted ...

TedBear
Valued Contributor
6 replies

Pic 2 inside through doorPic 3 Cube unit (rear) & doorPic 3a Cube Unit Wall and doorPic 3b Cube units & return wallPic 4 Timber upright & framingPi ...

SMS
New Contributor
6 replies

Hello! I was just wondering if this compressor would be a good idea and work with an air brush. This is the first time I'm going to give it a go, so ...

mb_580
New Contributor
12 replies

Hi everyone, happy new year to all, I made a workbench to organising my tools and clean-up my garage during last week (first week of holiday). I thou ...

3dMan
Newbie
3 replies

     this is a question about the elegoo neptune 2 stepper motor for the z axis with the 2 screw that connect it to the frame

Wayne
Super Contributor
11 replies

My first project at the XMRC Shed - a Semi Trailer Mack Truck Model.I bought the Plans for this model quite some time ago but never seemed to be able ...

JustinMcAbbe
New Contributor
3 replies

Hello Please can you provide some guidance on how best to install this heavy bag mount into garage ceiling; 1- How far are the beams in normal Aust ...

Pklebano
Budding Contributor
7 replies

Following on with the racing themeFully finished with the tie down points addedThe side rails increase stiffness and hold the edge of the vinylA coat ...

Kruzon
Budding Contributor
8 replies

Hi, I was trying to make a fishing rod storage tube using PVCs by following this Youtube tutorial (https://www.youtube.com/watch?app=desktop&v=nY6FmrB ...

fhk56
Budding Contributor
5 replies

For many many years, I have been using plastic containers for small parts etc. After years of use these are now falling apart and spreading their cont ...

meexrose
New Contributor
4 replies

Hi! I've bought a bunch of Connect-it anodised aluminium square tubes to make a frame for my catio. I've had no issues drilling the holes needed to se ...

Moderator Walter
Moderator
13 replies

Hey everyone, this is a bit left field, but I do a lot of 3D printing, and among external things (not the printer equipment) you have to consider are: ...

Madmoggy
Established Contributor
1 reply

If you’re anything like normal (My excuse) I always tear masking tape etc off and when I go for the next piece I have to run my nail around the roll ...

ivanptr
Senior Contributor
3 replies

Hi everyone, We followed an online advice to make a diy temporary ramp curb using these safety cushion matt from bunnings. Works better than expectati ...

bilcruise
Established Contributor
20 replies

Hi, I am thinking to build a weightlifting platform for my garage gym, something like this. As you can see the bottom layer is built by abo ...

sugachim1310
Newbie
1 reply

Will a Holman 32mm Press PVC Cap End fit onto a Holman 32mm Class 12 PVC Pressure Pipe, I was reading the reviews and one customer said that it was to ...

J_Smart
Junior Contributor
21 replies

Hi all,I have a bit of a conundrum and am running out of space in my current workshop DIY area.I believe I can use the space a bit more efficiently bu ...

Johnson
Budding Contributor
6 replies

I plan to hang a boxing bag with the wall bracket (see link below) on a 70s yellow brick wall in my garage. It does not come with any wall plug or ins ...

minabina
New Contributor
8 replies

Hello, Pilates equipment is ridiculously expensive so I have chosen to make my own for use at home. I have made a makeshift Pilates "Springboard" usi ...

Brad
Trusted Contributor
1 reply

Had a play with the new toys. Banksia Cones went into a pressure pot with resin. ( photos later when finished ) The leftovers I tried some things ...