Workshop
Start a discussion

Topics with Label: Furniture

mich1972
Super Contributor
4 replies

Hello Workshop Community !!!!!  My hubby’s Mum recently downsized to a Unit. We were lucky to salvage the very old and forgotten Jarrah workbench in ...

Nikki7
New Contributor
7 replies

Long time stalker and first time poster. After seeing all these amazing things being built I decided to have a crack at making my own work area. Gener ...

mike79
New Contributor
5 replies

Hi, I have decided to build myself a workbench for woodworking and would like to focus on more hand tool joinery. I have made smaller projects so hav ...

Nettie
New Contributor
3 replies

I have an old bar that has maroon coloured vinyl around the outside. It's it possible to paint, rather than replace, the vinyl?

JoeAzza
Experienced Contributor
14 replies

I have just completed making and installing shelves and duct cover for a range hood cupboard for my nephews new place, I new he had no work benches to ...

Neo19
Established Contributor
9 replies

Hello friendly workshopers, I have been looking for ideas to build a compact and neat workbench in the garage that is already crammed with things. Goo ...

DanManc
New Contributor
9 replies

Hi I need to cut a hole for my patio umbrella in the middle of my 6 seater aluminium outdoor table. i need advice on what to use, how to use it and h ...

Peter7
New Contributor
2 replies

I am assembling a PRACTA 1000mm base cabinet, the sections of which are joined together by cams and pins. I have connected all panels except the last ...

theskywaspink
Junior Contributor
14 replies

Hi all, I've been a reader for a while but not posted anything. It's been a long time since I've touched any power tools for a lengthy time, but still ...

Shagen
Junior Contributor
3 replies

I am hoping to get some tips on which jigsaw i should get. I am a novice and just started out doing little projects. While I was looking for a jigsaw ...

Shagen
Junior Contributor
15 replies

Hi, I am new here. This is a great community with lots of ideas. I have a question which I hope someone with more knowledge and experience can help. ...

DungeonDweller
Budding Contributor
10 replies

WHERE DA GAMER'S AT? Hey everyone. Thought I'd post a pic of my ISO WIP. It's going to be a board game table. The flat screen insert is so I can us ...

MonkeyLearn
Junior Contributor
6 replies

I'm building a few things out of pallets including shelves, tables etc. and I was wondering about what the best way to finish them would be. I have a ...

KevinMall
Established Contributor
1 reply

Hi all, I am a complete newcomber and this timber workbench is my first major project. Last night it was "repurposed" as a party table for my daught ...

Arcc
Junior Contributor
33 replies

Needing to organise and store my powertools I undertook this little project. Built almost entirely from wood repurposed from crates and pallets it w ...

akshayakate
New Contributor
5 replies

Hi Workshoppers!I am new to Ballarat and I am passionate about woodworking. Unfortunately I did not have any practical education in trades while in sc ...

Arcc
Junior Contributor
3 replies

Preparing the wood. Clamping to try and straighten it as much as possible.Adding extra weight to the clamps. Then off to south africa for a 6 week hol ...

petrolhead
Budding Contributor
12 replies

He’s a walk-through of what we have progressed to in the build of this man cave/sleepout/shed garage.

kbcreations
New Contributor
3 replies

chrissq
New Contributor
1 reply

At 60 I have joined a local Men's Shed and learning woodworking which I have not touched for over 40 years. I have access to some wonderful tools but ...

JustJim
Established Contributor
4 replies

My back isn't what it used to be, and to be honest, it didn't used to be much good anyway. So when I found myself hunched over my already raised assem ...

RodAndo
Junior Contributor
4 replies

jhodges
New Contributor
6 replies

I am trying to make a coffee table from a live edge slab of camphor laurel. I’ve used a belt sander and random orbital sander however I’ve not been ab ...

AndrewJones
Experienced Contributor
16 replies