Workshop
Ask a question

Topics with Label: Tools and Materials

bennib0i
Just Starting Out
4 replies

Hi Bunnings, I'm repainting one of my bedrooms and would like to get rid of this old Foxtel Outlet. I think there are 2 old coaxial cables here wh ...

Djole
Community Newcomer
1 reply

Hey All, I have a couple of cup sized holes in my internal plastered brick wall in the living room. It was to conceal a cable in the wall, but now w ...

Terrie
Just Starting Out
1 reply

How do I measure and install an internal door jam

nugley
Building a Reputation
5 replies

As shown in the image, I have 3 ceiling cracks. These cracks run in between ceiling joists that are spaced 600mm. There is a noggin behind the middle ...

Jeaniek
Finding My Feet
5 replies

Hello Somebody Please Help, I've just bought an Smith Corona Deville 510 Electric Typewriter. It's a 110 - 130v 60hz power, so to get it to work will ...

aton5
Cultivating a Following
14 replies

Have a standard door leading out to the garage, the door is latching but the lock is not locking. I think there is a misalignment with the strike p ...

Jamespeter100
Making a Splash
2 replies

Wheels spin on the end if the dowel. Don’t want the press fir to spin the dowel incase it catches long hair. A UV stabilised marker can be used for th ...

Samc1234
Cultivating a Following
1 reply

Hi, I am wanting to use a piece of stair thread timber around 1.8m long, 30cm deep and 6-7cm thick to create a floating entry way bench. my house ...

dunnycan
Finding My Feet
3 replies

Hi, I used plywood for my wardrobe because it needs to hold the weight of vertical bars. Just wondering for the seams can I use Selleys Spakfilla Rapi ...

redbackspider77
Just Starting Out
5 replies

Hi all, I am planning to build a solid timber bookshelf that is 2-2.2m tall and at least 30cm deep. However, I am struggling to find an applicable m ...

YasHaskell
Just Starting Out
6 replies

Hi, I have just moved into my new (old) villa and want to hang some pictures. The units were built in the 60s and renovated at various times. There ar ...

zurc
Just Starting Out
1 reply

 Replacing clip on vertical blind? Below clip has broken and the blind keeps falling off. Where/how can I replace this clip?

DannyN
Getting Established
5 replies

My master bedroom has an ensuite, and the floor area right outside the bathroom door often gets water on it. Is there anything I can do to stop ...

trish-b
Finding My Feet
2 replies

 Honouring the past. Designing for now. This was originally a dresser which I cut in half and made into two bedsides this is the first of two. I’ve ha ...

kstroll
Finding My Feet
2 replies

Hi, I have some paint flaking off (after restumping) and want to paint over this textured paint so it's a smooth finish. Do i need to sand and then us ...

AmyC
Just Starting Out
1 reply

Hi all, I would like your urgent help to remove the stuck door latch of a bedroom door. We have a Bunnings Ikonic Brushed Nickel Norr Passage Lever ...

landasamuel
Finding My Feet
2 replies

We are about to pour self leveling concrete to even the floor, what primer should we use with bastion floor leveller?

HandyUser59
Just Starting Out
2 replies

Hi Bought an Ikonic privacy handle for 35 to 45mm doors . My door is 35mm thick. However the spindle is stuck at 45 mm, how do i get the handles to f ...

ajlb
Just Starting Out
2 replies

  I have two of these towers and haave had them cut down to 1845cm height to match the pre-existing and installed batten on the side. What is the ...

Innov8tive
Building a Reputation
2 replies

I'm just wanting to replace this air vent grille in the hallway. I'm assuming it just would snap off and the new one would snap in. Does Bunning ...

jarrahlo
Just Starting Out
4 replies

 What is the easiest way to change the doors from swinging to sliding doors? What are the best doors and tracks to buy. I want a wooden Hampton kind ...

SPP
Having an Impact
4 replies

My floor joist has been damaged by fire. See attached photos. How do I URGENTLY repair this?

DominicPI
Finding My Feet
1 reply

Hey all looking for a quick idea if anyone can help me: I have this desk from Office Works, which I bought about 2 years ago:https://www.officeworks.c ...

ohce
Just Starting Out
2 replies

  Hi folks, I’ve had our 40-year-old timber windows replaced with aluminium ones, as a result wooden architraves were removed and the galvanized stee ...